What the Mounting Combo 1600 does on a busy floor
The Mounting Combo 1600 is a wide-format cold and heat assisted machine for applying laminate film and mounting printed sheets onto board. It is aimed at work where you want the print to stay flat, resist handling and look tidy at the edge. For shops in Johannesburg, Pretoria or the East Rand that turn around framed graphics, display boards, POS panels and presentation work, this unit gives you a controlled press without needing to piece jobs together in stages.
The main advantage is pressure control. When a board is not pressed evenly, you get bubbles, silvering, lifted corners or a wavy surface. This unit is designed to reduce that risk and keep pressure across the full width, which helps on coated prints, photo paper, vinyl prints and mounted artwork. It also suits repeat work, so the operator can set a method and keep the result consistent from job to job.
- Designed for laminating and board mounting in one workflow
- Suitable for short runs, repeat orders and presentation work
- Helpful where a clean finish matters more than speed alone
- Works well for shops that handle prints of different thicknesses
Sizes, film widths and the kinds of jobs it handles
The 1600 in the model name refers to the working width, which is 1600 mm, or 1.6 metres. That gives enough room for common signage panels, mounted posters and wide art prints without forcing awkward joins. If you work with A1, A0, 1000 mm graphics or mixed board sizes, the width makes day to day use more practical.
This type of machine is often chosen by shops that need one unit to handle both finishing and mounting. It is useful for canvas prints, display boards, exhibition panels, window graphics on rigid sheet and artwork that must go out looking neat. It is not only for big print houses either, smaller studios in Sandton, Randburg or Midrand often use this size because it fits local demand without taking over the floor.
- Working width: 1600 mm
- Handles common sheet sizes and board formats up to 1.6 metres wide
- Suitable for laminating film, mounting film and pressure based finishing
- Good fit for printed boards used in retail, events and interiors
Where the 1600 model fits best in South African work
This machine suits businesses that deal with mounted presentation pieces, school signage, estate agent boards, exhibition graphics, retail displays and gallery work. In coastal areas like Durban or Gqeberha, clean mounting also helps protect prints from humidity when the right media is used. In Gauteng, where shops often run tight turnaround times, the unit is valued for its predictable pressure and straightforward handling.
It is also a sensible option for teams that do not want to send mounting work out to a third party. Keeping the job in house helps with deadlines, colour matching and reprints. If you are in a branch network or you service clients in Pretoria, East Rand and the surrounding industrial zones, the 1600 size gives a practical middle ground between tabletop units and very large production lines.
- Print shops and digital finishers
- Graphic designers handling presentation boards
- Artists preparing edition work or exhibition pieces
- Signage teams mounting foam board, PVC board or similar sheet stock
Power, setup and installation notes before the machine arrives
Before ordering, check your floor space, access route and power supply. The machine needs a level position, enough room at the infeed and outfeed, and a stable electrical supply that can handle the load. In areas where load-shedding is still part of daily planning, many businesses also look at inverter support or generator backup for controlled shutdowns and to avoid interrupted heating or drive cycles.
For installation, allow for clear access through doors, roller shutters and ramps. If the machine is being taken to Kya Sand, Sandton, Pretoria or further afield, measure the route from the delivery point to the final position. Also check whether you need single phase or three phase power, because that affects where the unit can be placed and what is required from your electrician. A neat install makes servicing easier later and reduces downtime when the line is busy.
- Confirm available power supply before purchase
- Check floor level, access width and turning space
- Plan for load-shedding backup if production cannot stop
- Use a qualified electrician for final connection and verification
Care, cleaning and service that keep pressure even
Like any finishing machine, the Mounting Combo 1600 works best when the rollers and pressure system are kept clean. Glue overspray, dust and backing paper scraps can affect grip and leave marks on the finished board. Routine roller cleaning and pressure calibration help keep the machine set correctly. That matters when you are doing repeated jobs for the same customer and the finish has to match from one order to the next.
Heat system checks and drive system checks are worth doing on a schedule, not only when something goes wrong. If a motor starts to sound different, if the feed is drifting or if the pressure feels off in one side, it is better to stop and inspect it early. On the service side, we assist with routine servicing, electrical fault finding, on-site breakdowns, spare parts support and operator refresher training. A machine that is looked after properly lasts longer and gives fewer surprises in the middle of a rush, which is the point really.
- Clean rollers regularly to avoid marks and build-up
- Check pressure settings after heavy use or media changes
- Inspect heat and drive systems on a set service schedule
- Train operators to spot early signs of misalignment or wear
Points to confirm before ordering this laminator
When ordering a Mounting Combo 1600, confirm the exact width you need, the media types you plan to run and the board thicknesses you use most often. If your work changes between mounting foam board, composite sheet and laminated poster work, say so upfront so the spec matches the job mix. It also helps to know whether your team will run mostly cold work or needs heat assistance for specific materials.
You should also check the control layout, the feed direction, the type of pressure adjustment and what spare parts are held locally. If the unit will be used by more than one operator, ask for refresher training on setup and safe operation. For buyers comparing options in Kya Sand, Randburg, Midrand or further out, the right questions now save time later and reduce the chance of bringing in a machine that is too small or too limited for the actual workload.
- Width needed and maximum board size
- Cold only or heat assisted use
- Types of print media and board stock
- Power supply on site and backup plan
- Operator training and servicing requirements
Key facts
| Model | Mounting Combo 1600 |
|---|---|
| Working width | 1600 mm |
| Function | Laminating and mounting prints onto boards |
| Pressure control | Adjustable for even application across the width |
| Use type | Cold and heat assisted finishing depending on material |
| Typical applications | Posters, display boards, exhibition panels, photo work and artwork |
